1030 nm Laser

Item Code: 1030L-13B-NI-PT-NF

DPSSL SM fiber

Preliminary

Full production

Replacement in due course

Not for new designs

Orders still accepted, deliveries still possible

No more orders accepted

Discontinued

Available (in stock) Not in stock

Description

1030 nm DPSS laser features high power with very good TEM00 beam, with M2 of <1.2 and SM (single-mode) fiber only improves this parameter to outstanding 1.05. It is often used for inspection of optical components at around 1030 nm radiation wavelength. This DPSS laser is based on Yb:YAG gain medium, therefore, exhibits a very low quantum defect.

By default, this type of laser is built with FC/PC connector, but other fiber terminations are available upon request. Details about non-standard connector and the fiber used with it should be discussed with the Integrated Optics sales team.

Fiber Termination - FC/PC (PT): FC/PC has good insertion repeatability, therefore is often used in single-mode fiber applications. Features a key for polarization-maintaining fiber installations.

Last edited on: 10 July 2024

Parameter	Minimum Value	Typical Value	Maximum Value
Central wavelength, nm	1028	1030	1032
Longitudinal modes	-	Multiple	-
Spectral line width FWHM, nm	0.3	0.7	1.3
Output power, mW ¹	-	350	-
Power stability, % (RMS, 8 hrs) ²	0.01	0.1	0.3
Power stability, % (peak-to-peak, 8 hrs) ³	0.05	0.5	1.5
Intensity noise, % (RMS, 20 Hz to 20 MHz) ⁴	0.5	1.5	15
Transversal modes	-	TEM00	-
M² effective	-	1.05	1.1
Control interface type ⁵	-	UART	-
Operation mode	-	APC (CW)	-
Input voltage, VDC	4.8	5	5.3
External power supply requirement	-	+5 V DC, 5 A	-
Dimensions (WxDxH), mm ⁶	-	50 x 30 x 18	-
Fiber length, m	0.95	1	1.1
Heat-sinking requirement, °C/W	-	0.5	-
Optimum heatsink temperature, °C	15	20	30
Warm up time, mins (cold start)	0.2	1	2
Temperature stabilization	-	Internal TEC	-
Overheat protection	-	Yes	-
Storage temperature, °C (non-condensing)	-10	-	50
Net weight, kg	0.1	0.12	0.14
Max. power consumption, W	5	10	20
Warranty, months (op. hrs) ⁷	-	14 (10000)	-
RoHS	-	Yes	-
CE compliance	-	- General Product Safety Directive (GPSD) 2001/95/EC - (EMC) Directive 2004/108/EC	-
Laser safety class	-	3B	-
OEM lasers are not compliant with	-	IEC60825-1:2014 (compliant using additional accessories)	-
Country of origin	-	Lithuania	-

¹ The optical power can be tuned from virtually 0% to 100%. However, other specifications, such as central wavelength, power stability, noise, polarization ratio, beam shape, quality and circularity are not guaranteed at power levels other than factory preset power. Significantly worse power stability is to be expected at very low power levels, e.g. <3% from specified nominal power.

² The long term power test is carried out at constant laser body temperature (+/-0.1 ‎°C) using an optical power meter with an input bandwidth of 10 Hz. The actual measurement rate has a period of about 20 seconds to 1 minute.

³ The long term power test is carried out at constant laser body temperature (+/-0.1 ‎°C) using an optical power meter with an input bandwidth of 10 Hz. The actual measurement rate has a period of about 20 seconds to 1 minute.

⁴ Noise level is measured with a fast photodiode connected to an oscilloscope. The overall system bandwidth is from 2 kHz to 20 MHz.

⁵ Break-out-boxes AM-C8 and AM-C3 can be used for conversion of UART communication to either USB or RS232.

⁶ Excluding control interface pins and an output window/fiber assembly.

⁷ Whichever occurs first. The laser has an integrated operational hours counter.