520 nm Laser

Item Code: 0520L-13A-NI-PT-NF

Diode SM fiber

Preliminary

Full production

Replacement in due course

Not for new designs

Orders still accepted, deliveries still possible

No more orders accepted

Discontinued

Available (in stock) Not in stock

Description

Green laser sources are often used for fluorescence excitation, Raman scattering, as well as for Ti:sapphire pumping applications. High long-term power stability is ensured by TEC thermal stabilization, thermal and optical feedback. USB communication lets the laser be easily controlled by connecting it to the computer in any laboratory. The laser head includes all drive electronics within a single enclosure.

By default, this type of laser is built with FC/PC connector, but other fiber terminations are available upon request. Details about non-standard connector and the fiber used with it should be discussed with the Integrated Optics sales team.

Fiber Termination - FC/PC (PT): FC/PC has good insertion repeatability, therefore is often used in single-mode fiber applications. Features a key for polarization-maintaining fiber installations.

Last edited on: 18 April 2025

Parameter	Minimum Value	Typical Value	Maximum Value
Central wavelength, nm	515	520	530
Longitudinal modes	-	Multiple	-
Spectral line width FWHM, nm	0.02	2	3
Output power, mW ¹	-	60	-
Power stability, % (RMS, 8 hrs) ²	0.01	0.03	0.3
Power stability, % (peak-to-peak, 8 hrs) ³	0.1	0.4	1
Intensity noise, % (RMS, 20 Hz to 20 MHz) ⁴	0.1	0.4	1
Transversal modes	-	TEM00	-
M² effective	-	1.05	1.1
Control interface type ⁵	-	UART	-
Operation mode	-	APC (CW)	-
Modulation bandwidth, MHz ⁶	-	10	-
Input voltage, VDC	4.8	5	5.3
External power supply requirement	-	+5 V DC, 1.5 A	-
Dimensions (WxDxH), mm ⁷	-	50 x 30 x 18	-
Fiber length, m	0.95	1	1.1
Heat-sinking requirement, °C/W	-	1	-
Optimum heatsink temperature, °C	15	20	30
Warm up time, mins (cold start)	0.1	0.5	1
Temperature stabilization	-	Internal TEC	-
External fan control ⁸	-	No	-
Overheat protection	-10	Yes	50
Storage temperature, °C (non-condensing)	0.4	-	10
Net weight, kg	0.1	0.12	0.14
Max. power consumption, W	0.4	2	10
Warranty, months (op. hrs) ⁹	-	14 (10000)	-
RoHS	-	Yes	-
CE compliance	-	- General Product Safety Directive (GPSD) 2001/95/EC - (EMC) Directive 2004/108/EC	-
Laser safety class	-	3B	-
OEM lasers are not compliant with	-	IEC60825-1:2014 (compliant using additional accessories)	-
Country of origin	-	Lithuania	-

¹ The optical power can be tuned from virtually 0% to 100%. However, other specifications, such as central wavelength, power stability, noise, polarization ratio, beam shape, quality and circularity are not guaranteed at power levels other than factory preset power. Significantly worse power stability is to be expected at very low power levels, e.g. <3% from specified nominal power.

² The long term power test is carried out at constant laser body temperature (+/-0.1 ‎°C) using an optical power meter with an input bandwidth of 10 Hz. The actual measurement rate has a period of about 20 seconds to 1 minute.

³ The long term power test is carried out at constant laser body temperature (+/-0.1 ‎°C) using an optical power meter with an input bandwidth of 10 Hz. The actual measurement rate has a period of about 20 seconds to 1 minute.

⁴ Noise level is measured with a fast photodiode connected to an oscilloscope. The overall system bandwidth is from 2 kHz to 20 MHz.

⁵ Break-out-boxes AM-C8 and AM-C3 can be used for conversion of UART communication to either USB or RS232.

⁶ TTL digital modulation up to 10 MHz.

⁷ Excluding control interface pins and an output window/fiber assembly.

⁸ This function can be enabled in hardware only if the fast modulation option is disabled. The customer must specify this before ordering the laser.

⁹ Whichever occurs first. The laser has an integrated operational hours counter.

Typical spectrum

Typical spectrum of 0520 nm diode laser. Measured with 20 pm resolution.

Drawing

The key dimensions of a fiber-coupled MatchBox.

Typical Near Field

About Matchbox Datasheet Brochure Please log-in for downloads! Drawings Control Software (Windows)

Laser Diffraction Particle Analysis

None

Confocal Microscopy

Confocal microscopy is a powerful imaging technique used in biological and materials science research. By employing point illumination and a spatial pinhole, confocal microscopy eliminates out-of-focus light, resulting in sharper, high-resolution images. This method enables three-dimensional imaging of specimens with exceptional optical sectioning, making it valuable for studying biological structures and dynamic processes at the cellular and subcellular levels.

Food sorting

None

Flow Cytometry

Flow cytometry is a sophisticated analytical technique widely used in biomedical research and clinical diagnostics. It allows for the simultaneous analysis of multiple physical and chemical characteristics of cells or particles as they flow through a laser beam. By utilizing fluorescence and light-scattering principles, flow cytometry provides valuable insights into cell populations, allowing researchers to study cell morphology, identify cell types, and assess various cellular functions with high-throughput precision.

SLM Laser Essential Accessory Bundle